dhairya Alloys is are one of the main Manufacturers, Supplier and Exporters of Incoloy 800/825 Alloy Plates & Sheets. With the aide of skilled specialists, Champak Steel and Engg. Co are occupied with offering first rate Incoloy 800/825 Sheets and Plates on extensive scale. We offer them in plates and are exceedingly praised for its long organization life, durability and perfect results. These Incoloy 800/825 Sheets and Plates are versatile and are being given in the sensible rates to the supporters.
Specification for Incoloy 800/825 Alloy Plates & Sheets
| Steel Grades | Incoloy 800 – UNS N08800, Incoloy 800H / HT – UNS N08810, Incoloy 825 – UNS N08825 |
|---|---|
| Standard | ASTM / ASME SB 168, ASTM / ASME SB 424 , ASTM / ASME SB 443 |
| Production | Hot-Rolled (HR) / Cold-Rolled (CR) |
| Thickness | 1.0mm – 200mm |
| Width | 1000mm-3000mm |
| Application | Chemicals & Fertilizers Industries , Sugar Mills , Cement Industries , Ship Building , Paper Industries , Oil & Gas , Petrochemicals , etc |
Chemical Composition for Incoloy 800 Alloy Plates & Sheets
| Incoloy | 800 | 800H | 800HT |
|---|---|---|---|
| Ni | 30-35 | 30-35 | 30-35 |
| Fe | 39.5 min | 39.5 min | 39.5 min |
| Cr | 19-23 | 19-23 | 19-23 |
| Cu | 0.75 max | 0.75 max | 0.75 max |
| Ti | 0.15-0.60 | 0.15-0.60 | 0.25-0.60 |
| Al | 0.15-0.60 | 0.15-0.60 | 0.85-1.20 |
| C | 0.1 max | 0.05-0.1 | 0.06-0.1 |
| Mn | 1.5 max | 1.5 max | 1.5 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| Si | 1.0 max | 1.0 max | 1.0 max |
Chemical Composition for Incoloy 825 Alloy Plates & Sheets
| Incoloy 825 | Ni | Fe | C | Mn | Si | Mb | Cu | Cr | Al | Ti | S |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 38.0 – 46.0 | 22.0 min | 0.05 max | 1.0 max | 0.5 max | 2.5 - 3.5 | 1.5 - 3.0 | 19.5 - 23.5 | 0.2 max | 0.6 - 1.2 | 0.015 max |
Driven by in fact propelled offices at our ultra-advanced assembling unit, we are introducing a broad scope of Incoloy Alloy 800/800HT/825 Round Bars & Rods. Our offered extent is absolutely made by our gifted experts by making utilization of forefront innovation and quality tested in consistence with set general standards.
Specification
| Standard | ASTM / ASME SB 166, ASTM / ASME B 446 , ASTM / ASME B 637, ASTM B 511, ASTM B 408 |
|---|---|
| Grade | Incoloy 800 (UNS N08800) Incoloy 800H (UNS N08810) Incoloy 800HT (UNS N08811) Incoloy 825(UNS N08825). |
| Range | 5MM DIA - 500MM DIA |
| Length | 100MM - 6000MM |
| Finish | Bright, Polish & Black |
| Form | Round, Square, Hex (A/F), Rectangle, Wire (Coil Form), Wire-mesh, Billet, Ingot, Forging Etc |
Chemical Composition
| Incoloy | 800 | 800H | 825 |
|---|---|---|---|
| Ni | 30-35 | 30-35 | 38.0 – 46.0 |
| Fe | 39.5 min | 39.5 min | 22.0 min |
| Cr | 19-23 | 19-23 | 19.5 - 23.5 |
| Cu | 0.75 max | 0.75 max | 1.5 - 3.0 |
| Ti | 0.15-0.60 | 0.15-0.60 | 0.6 - 1.2 |
| Al | 0.15-0.60 | 0.15-0.60 | 0.2 max |
| C | 0.1 max | 0.05-0.1 | 0.05 max |
| Mn | 1.5 max | 1.5 max | 1.0 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| Si | 1.0 max | 1.0 max | 0.5 max |
| Mb | - | - | 2.5 - 3.5 |
Mechanical Properties
| Inconel 800/800HT | |
|---|---|
| Tensile Strength | Psi – 75,000 , MPa – 520 |
| Yield Strength (0.2%Offset) | Psi – 30,000 , MPa –205 |
| Elongation | 30 % |
| Inconel 825 | |
| Tensile Strength | Psi – 80,000 , MPa – 550 |
| Yield Strength (0.2%Offset) | Psi – 32,000 , MPa –220 |
| Elongation | 30 % |
Physical Properties of Incoloy 800/800HT
| Density lbm/in3 |
Thermal Conductivity (BTU/h ft. °F) |
Electrical Resistivity (in x 10-6) |
Modulus of Elasticity (psi x 106 |
Coefficient of Thermal Expansion (in/in)/ °F x 10-6 |
Specific Heat (BTU/lb/ °F) |
Melting Range (°F) |
|---|---|---|---|---|---|---|
| at 68°F: 0.285 | 9.4 at 212°F | 28.3 at 68°F | 28 | 9.4 at 32 – 212°F | 0.1200 at 68°F to 212°F | 2500 to 2590 |
| 12.4 at 932 °F | 39.4 at 752°F | 10.2 at 32 – 1000°F | ||||
| 49.6 at 1652 °F | 10.4 at 32 – 1500°F |
Physical Properties of Incoloy 825
| Density | 8.14 g/cm3 |
|---|---|
| Melting Point | 1400 °C (2550 °F) |
.jpg)
Dhairya Alloy is a prestigious association that is moderately occupied with offering an extensive variety of Incoloy 800/800HT/825 Pipes and Tubes. Offered by us, these Incoloy 800/800HT/825 Pipes and Tubes are to a great degree refreshing among our supporters for their rich elements, for example, corrosion resistant, high tensile strength, robust design, flawless finish and durability.br>
Specification Of Incoloy Alloy 800/800HT/825 Seamless Welded Pipes And Tubes
| Grade | Incoloy 800 – UNS N08800, Incoloy 800H / HT – UNS N08810, Incoloy 825 – UNS N08825 |
|---|---|
| Size | ½”NB – 24”NB |
| Schedule | SCH 10 – SCH XXS |
| Type | Seamless / ERW / Welded / Fabricated / LSAW Pipes |
| Standards | ASTM B407, ASTM B163, ASTM B358, ASTM B515, ASME SB407, ASME SB163, ASME SB358, ASME SB 515 |
| End | Plain End, Beveled End, Threaded. |
| Length | Single Random, Double Random & Cut Length. |
| Form | Round, Square, Rectangular, Hydraulic Etc. |
Chemical Composition Of Incoloy Alloy 800/800HT/825 Seamless Welded Pipes And Tubes
| Incoloy | 800 | 800H | 825 |
|---|---|---|---|
| Ni | 30-35 | 30-35 | 38.0 – 46.0 |
| Fe | 39.5 min | 39.5 min | 22.0 min |
| Cr | 19-23 | 19-23 | 19.5 - 23.5 |
| Cu | 0.75 max | 0.75 max | 1.5 - 3.0 |
| Ti | 0.15-0.60 | 0.15-0.60 | 0.6 - 1.2 |
| Al | 0.15-0.60 | 0.15-0.60 | 0.2 max |
| C | 0.1 max | 0.05-0.1 | 0.05 max |
| Mn | 1.5 max | 1.5 max | 1.0 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| Si | 1.0 max | 1.0 max | 0.5 max |
| Mb | - | - | 2.5 - 3.5 |
Mechanical Properties Of Incoloy Alloy 800/800HT/825 Seamless Welded Pipes And Tubes
| Inconel 800/800HT | |
|---|---|
| Tensile Strength | Psi – 75,000 , MPa – 520 |
| Yield Strength (0.2%Offset) | Psi – 30,000 , MPa –205 |
| Elongation | 30 % |
| Inconel 825 | |
| Tensile Strength | Psi – 80,000 , MPa – 550 |
| Yield Strength (0.2%Offset) | Psi – 32,000 , MPa –220 |
| Elongation | 30 % |
Physical Properties of Incoloy 800/800HT
| Density lbm/in3 |
Thermal Conductivity (BTU/h ft. °F) |
Electrical Resistivity (in x 10-6) |
Modulus of Elasticity (psi x 106 |
Coefficient of Thermal Expansion (in/in)/ °F x 10-6 |
Specific Heat (BTU/lb/ °F) |
Melting Range (°F) |
|---|---|---|---|---|---|---|
| at 68°F: 0.285 | 9.4 at 212°F | 28.3 at 68°F | 28 | 9.4 at 32 – 212°F | 0.1200 at 68°F to 212°F | 2500 to 2590 |
| 12.4 at 932 °F | 39.4 at 752°F | 10.2 at 32 – 1000°F | ||||
| 49.6 at 1652 °F | 10.4 at 32 – 1500°F |
Physical Properties of Incoloy 825
| Density | 8.14 g/cm3 |
|---|---|
| Melting Point | 1400 °C (2550 °F) |
AsAs an abundantly appreciated association in the business sector, we as Champak Steel and Engg. Co. are entirely occupied with proposing an accumulation of Incoloy Alloy 800, 800HT, 825 Flanges as an exporter, producer, supplier, and stockiest to our overall customers at sensibly valued expenses. We are viewed as a prominent supplier and maker of a huge aggregation of such Flanges. Concerning distinctive evaluations, we offer these Incoloy Alloy 800, 800HT, 825 Flanges in various sorts.
Specification of Flanges
| Grade | Incoloy 800 (UNS N08800) Incoloy 800H (UNS N08810) Incoloy 800HT (UNS N08811) Incoloy 825(UNS N08825) |
|---|---|
| Werkstoff Nr | 1.4876/4958/59/2.4858 |
| Standards | ASTM, ASME Flanges, ANSI Flanges, DIN Flanges, EN Flanges, BS Flanges etc. |
| Specifications | ASTM B 564 / ASME SB 564 |
| Dimensions Std. | ANSI B16.5, ANSI B16.47 Series A & B, MSS SP44, ASA, API-605, AWWA, Custom Drawings |
| Size | 1/2” NB - 48″ NB |
| Class | 150#, 300#, 600#, 900#, 1500#, 2500# , etc |
| Pressure | DIN PN6, PN10, PN16, PN25, PN40, PN64, PN100, PN160 , etc |
Types of Flanges
| Incoloy Blind Flanges | Incoloy Reducing Flanges | Incoloy Ring Type Flanges |
| Incoloy Spectacle Flanges | Incoloy Weld Neck Flanges | Incoloy High Hub Flanges |
| Incoloy Threaded Flanges | Incoloy Lap Joint Flanges | Incoloy Long weld Neck Flanges |
| Incoloy Slip-On Flanges | Incoloy Socket Weld Flanges | Incoloy Orifice Flanges |
Chemical Composition
| Incoloy | 800 | 800H | 825 |
|---|---|---|---|
| Ni | 30-35 | 30-35 | 38.0 – 46.0 |
| Fe | 39.5 min | 39.5 min | 22.0 min |
| Cr | 19-23 | 19-23 | 19.5 - 23.5 |
| Cu | 0.75 max | 0.75 max | 1.5 - 3.0 |
| Ti | 0.15-0.60 | 0.15-0.60 | 0.6 - 1.2 |
| Al | 0.15-0.60 | 0.15-0.60 | 0.2 max |
| C | 0.1 max | 0.05-0.1 | 0.05 max |
| Mn | 1.5 max | 1.5 max | 1.0 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| Si | 1.0 max | 1.0 max | 0.5 max |
| Mb | - | - | 2.5 - 3.5 |
Mechanical Properties
| Inconel 800/800HT | |
|---|---|
| Tensile Strength | Psi – 75,000 , MPa – 520 |
| Yield Strength (0.2%Offset) | Psi – 30,000 , MPa –205 |
| Elongation | 30 % |
| Inconel 825 | |
| Tensile Strength | Psi – 80,000 , MPa – 550 |
| Yield Strength (0.2%Offset) | Psi – 32,000 , MPa –220 |
| Elongation | 30 % |
Physical Properties of Incoloy 800/800HT
| Density lbm/in3 |
Thermal Conductivity (BTU/h ft. °F) |
Electrical Resistivity (in x 10-6) |
Modulus of Elasticity (psi x 106 |
Coefficient of Thermal Expansion (in/in)/ °F x 10-6 |
Specific Heat (BTU/lb/ °F) |
Melting Range (°F) |
|---|---|---|---|---|---|---|
| at 68°F: 0.285 | 9.4 at 212°F | 28.3 at 68°F | 28 | 9.4 at 32 – 212°F | 0.1200 at 68°F to 212°F | 2500 to 2590 |
| 12.4 at 932 °F | 39.4 at 752°F | 10.2 at 32 – 1000°F | ||||
| 49.6 at 1652 °F | 10.4 at 32 – 1500°F |
Physical Properties of Incoloy 825
| Density | 8.14 g/cm3 |
|---|---|
| Melting Point | 1400 °C (2550 °F) |
As an abundantly appreciated association in the business sector, we as Dhairya Alloys are entirely occupied with proposing an accumulation of Incoloy Alloy 800, 800HT, 825 Buttweld Fittings as an exporter, producer, supplier, and stockiest to our overall customers at sensibly valued expenses. We are viewed as a prominent supplier and maker of a huge aggregation of such Buttweld Fittings. Concerning distinctive evaluations, we offer these Incoloy Alloy 800, 800HT, 825 Buttweld Fittings in various sorts.
Specification of Buttweld Fittings
| Grade | Incoloy 800 (UNS N08800) Incoloy 800H (UNS N08810) Incoloy 800HT (UNS N08811) Incoloy 825(UNS N08825) |
|---|---|
| Dimension Std. | ASTM, ASME ANSI B16.9, B16.28, MSS-SP-43. |
| Specification | ASTM B 366 / ASME SB 366 |
| Size | ½”NB - 48″NB |
| Schedule | SCH 10 – SCH XXS |
| Type | Seamless / Welded / Fabricated. |
Types of Buttweld Fittings
| Incoloy Reducers | Incoloy Concentric Reducers | Incoloy Tees |
| Incoloy Weldolet | Incoloy Short Stub End | Incoloy Eccentric Reducers |
| Incoloy Elbows | Incoloy 3D Elbow | Incoloy Lap Joint Stub End |
| Incoloy End Caps | Incoloy 5D Elbow | Incoloy 180° SR Return Bends |
| Incoloy Elbows | Incoloy Short Radius Elbow | Incoloy 45° Elbows |
| Incoloy Reducing Elbow | Incoloy Long Radius Elbow | Incoloy 180° LR Return Bends |
| Incoloy 45° Elbows | Incoloy Equal Tee | Incoloy UnEqual Tee |
| Incoloy Reducing Tee | Incoloy 1D Elbow | Incoloy 1.5D Elbow |
| Incoloy Long Stub Ends | Incoloy 2D Elbow | Incoloy 6D Elbow |
Chemical Composition
| Incoloy | 800 | 800H | 825 |
|---|---|---|---|
| Ni | 30-35 | 30-35 | 38.0 – 46.0 |
| Fe | 39.5 min | 39.5 min | 22.0 min |
| Cr | 19-23 | 19-23 | 19.5 - 23.5 |
| Cu | 0.75 max | 0.75 max | 1.5 - 3.0 |
| Ti | 0.15-0.60 | 0.15-0.60 | 0.6 - 1.2 |
| Al | 0.15-0.60 | 0.15-0.60 | 0.2 max |
| C | 0.1 max | 0.05-0.1 | 0.05 max |
| Mn | 1.5 max | 1.5 max | 1.0 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| Si | 1.0 max | 1.0 max | 0.5 max |
| Mb | - | - | 2.5 - 3.5 |
Mechanical Properties
| Inconel 800/800HT | |
|---|---|
| Tensile Strength | Psi – 75,000 , MPa – 520 |
| Yield Strength (0.2%Offset) | Psi – 30,000 , MPa –205 |
| Elongation | 30 % |
| Inconel 825 | |
| Tensile Strength | Psi – 80,000 , MPa – 550 |
| Yield Strength (0.2%Offset) | Psi – 32,000 , MPa –220 |
| Elongation | 30 % |
Physical Properties of Incoloy 800/800HT
| Density lbm/in3 |
Thermal Conductivity (BTU/h ft. °F) |
Electrical Resistivity (in x 10-6) |
Modulus of Elasticity (psi x 106 |
Coefficient of Thermal Expansion (in/in)/ °F x 10-6 |
Specific Heat (BTU/lb/ °F) |
Melting Range (°F) |
|---|---|---|---|---|---|---|
| at 68°F: 0.285 | 9.4 at 212°F | 28.3 at 68°F | 28 | 9.4 at 32 – 212°F | 0.1200 at 68°F to 212°F | 2500 to 2590 |
| 12.4 at 932 °F | 39.4 at 752°F | 10.2 at 32 – 1000°F | ||||
| 49.6 at 1652 °F | 10.4 at 32 – 1500°F |
Physical Properties of Incoloy 825
| Density | 8.14 g/cm3 |
|---|---|
| Melting Point | 1400 °C (2550 °F) |
As an abundantly appreciated association in the business sector, we as Champak Steel and Engg. Co. are entirely occupied with proposing an accumulation of Incoloy Alloy 800, 800HT, 825 Forged Fittings as an exporter, producer, supplier, and stockiest to our overall customers at sensibly valued expenses. We are viewed as a prominent supplier and maker of a huge aggregation of such Forged Fittings. Concerning distinctive evaluations, we offer these Incoloy Alloy 800, 800HT, 825 Forged Fittings in various sorts.
Specification of Forged Fittings
| Grade | Incoloy 800 (UNS N08800) Incoloy 800H (UNS N08810) Incoloy 800HT (UNS N08811) Incoloy 825(UNS N08825) |
|---|---|
| Dimension Std. | ASTM, ASME ANSI B16.11 & BS3799, etc. |
| Specification | ASTM/ASME B/SB 564 / 160 / 472 |
| Size | ½” NB - 4” NB |
| Class | 2000LBS, 3000LBS, 6000LBS, 9000LBS, etc |
| Type | Socket Weld (S/W) & SCREWED (SCRD) – NPT, BSP, BSPT, Threaded Fittings |
Types of Forged Fittings
| Incoloy Socket Weld Caps | Incoloy Socket Weld Tee | Incoloy Socket Weld Unions |
| Incoloy Couplings | Incoloy Forged Reducers | Incoloy Socket Weld Cross |
| Incoloy Socket Weld 90° Elbows | Incoloy Socket Weld Full Coupling | Incoloy Socket Weld Half Coupling |
| Incoloy Socket Weld 45° Elbows | Incoloy Socket Weld Reducing Coupling | Incoloy Screwed Unions |
| Incoloy Screwed 45° Elbows | Incoloy Screwed 90° Elbows | Incoloy Screwed Tee |
| Incoloy Screwed Cross | Incoloy Screwed Hex Plug | Incoloy Screwed Squared Plug |
| Incoloy Screwed Hex Nipple | Incoloy Screwed Bushing | Incoloy Screwed Full Coupling |
| Incoloy Screwed Half Couplings | Incoloy Screwed Reducing Couplings | Incoloy Screwed Caps |
| Incoloy Weldolet | Incoloy Sockolet | Incoloy Threadolet |
| Incoloy Elbolet | Incoloy Nipolet | Incoloy Latrolet |
| Incoloy Concentric Swage Nipple | Incoloy Eccentric Swage Nipple | Incoloy Forged Pipe Nipple |
Chemical Composition
| Incoloy | 800 | 800H | 825 |
|---|---|---|---|
| Ni | 30-35 | 30-35 | 38.0 – 46.0 |
| Fe | 39.5 min | 39.5 min | 22.0 min |
| Cr | 19-23 | 19-23 | 19.5 - 23.5 |
| Cu | 0.75 max | 0.75 max | 1.5 - 3.0 |
| Ti | 0.15-0.60 | 0.15-0.60 | 0.6 - 1.2 |
| Al | 0.15-0.60 | 0.15-0.60 | 0.2 max |
| C | 0.1 max | 0.05-0.1 | 0.05 max |
| Mn | 1.5 max | 1.5 max | 1.0 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| Si | 1.0 max | 1.0 max | 0.5 max |
| Mb | - | - | 2.5 - 3.5 |
Mechanical Properties
| Inconel 800/800HT | |
|---|---|
| Tensile Strength | Psi – 75,000 , MPa – 520 |
| Yield Strength (0.2%Offset) | Psi – 30,000 , MPa –205 |
| Elongation | 30 % |
| Inconel 825 | |
| Tensile Strength | Psi – 80,000 , MPa – 550 |
| Yield Strength (0.2%Offset) | Psi – 32,000 , MPa –220 |
| Elongation | 30 % |
Physical Properties of Incoloy 800/800HT
| Density lbm/in3 |
Thermal Conductivity (BTU/h ft. °F) |
Electrical Resistivity (in x 10-6) |
Modulus of Elasticity (psi x 106 |
Coefficient of Thermal Expansion (in/in)/ °F x 10-6 |
Specific Heat (BTU/lb/ °F) |
Melting Range (°F) |
|---|---|---|---|---|---|---|
| at 68°F: 0.285 | 9.4 at 212°F | 28.3 at 68°F | 28 | 9.4 at 32 – 212°F | 0.1200 at 68°F to 212°F | 2500 to 2590 |
| 12.4 at 932 °F | 39.4 at 752°F | 10.2 at 32 – 1000°F | ||||
| 49.6 at 1652 °F | 10.4 at 32 – 1500°F |
Physical Properties of Incoloy 825
| Density | 8.14 g/cm3 |
|---|---|
| Melting Point | 1400 °C (2550 °F) |